Sensors
Showing 1–15 of 34 results
- Sensors
Turbidity Sensor || Turbidity Detection Sensor Module with Probe Kit
- Working voltage: DC5V; Operating Current : 30mA (MAX)
- Response time : <500ms
- Insulation Resistance : 100M Ω[Min];
- Works with microcontroller – Can’t work alone (No Display)
- the output way: Analog output 0-4.5V
SKU: II_Turbidity Sensor - Sensors
ADXL345 3 Axis Digital Acceleration of Gravity Tilt Module for Arduino
- The adxl345 is a small, thin, low power, 3 axis mems accelerometer with high resolution (13bit) measurement at up to plus or 16 g
- Digital output data is formatted as 16bit two’s complement and is accessible through either an spi (3 or 4wire) or i2c digital interface
- Spi or i2c communication
SKU: Sensor_199 - Sensors
SOILSENSOR Soil Moisture Sensor
- This is a simple water sensor that can be used to detect soil moisture
- Can be used in module plant waterer device, and the plants in your garden no need people to manage
- Operating voltage: 3
- Module dual output mode, digital output, analog output more accurate
SKU: Sensor_soil - Sensors
HX711 Load Cell Amplifier Module
HX711 module is a Load Cell Amplifier breakout board for the HX711 IC that allows you to easily read load cells to measure weight. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. The input circuit can be configured to provide a bridge type pressure bridge (such as pressure, weighing sensor mode), is of high precision, low cost is an ideal sampling front-end module.
HX711 is an IC that allows you to easily integrate load cell into your project. No need of any amplifiers or dual power supply just use this board and you can easily interface it to any micro-controller to measure weight.
The HX711 uses a two wire interface (Clock and Data) for communication. Compared with other chips, HX711 has added advantages such as high integration, fast response, immunity, and other features improving the total performance and reliability. Finally it’s one among the best choices for electronic enthusiasts. The chip lowers the cost of the electronic scale,at the same time,improving performance and reliability.
SKU: Sensor_hx711 - Hardware Parts, Sensors
3Kg Load cell – Electronic Weighing Scale Sensor
A load cell is a transducer that is used to create an electrical signal whose magnitude is directly proportional to the force being measured. The various types of load cells include hydraulic load cells, pneumatic load cells and strain gauge load cells.
This is a standard load cell for measuring weight upto 3 Kg. The output of the load cell is in mili-volts and cannot be directly measured by a micro-controller. So an ADC with high resolution or an instrumentation amplifier is required to make the output of the load cell readable to a micro-controller.
SKU: Sensor_LC3kg - Accessories, Accessories, Sensors
NRF24L01 + 2.4GHZ Wireless Transceiver module for Arduino
1 low working voltage: 1.9 ~ 3.6V low voltage operation 2 high speed: 2Mbps, due to the transmission time is very short, greatly reducing the collision phenomenon in the wireless transmission (air transmission rate software set 1Mbps or 2Mbps) 3 multi frequency: 125 frequency points, meet the multipoint communication and frequency hopping communication needs 4 tiny: built-in 2.4GHz antenna, small volume, 15x29mm (including antenna) 5 low power: when working in answer mode communication, air transport and starting time of fast, greatly reducing current consumption. 6 low cost: the NRF24L01 integrates all the relevant RF agreements and high-speed signal processing, such as: automatic retransmission of lost packets and automatically generate a response signal, SPI interface, NRF24L01 can use the hardware SPI port connection or by SCM I/O port simulation, internal FIFO and all kinds of high and low speed microprocessor interface, easy to use low cost microcontroller.
SKU: sensor_nrf24l01 - Sensors
MQ135 MQ-135 Air Quality Sensor Hazardous Gas Detection Module For Arduino
Input voltage: DC5V power (current): 150mA
Analog output with increasing concentration, the higher the concentration, the higher the voltage.
A hazardous gas detection apparatus for the family, the environment. Suitable for ammonia, aromatic compounds, sulfur, benzene vapor, smoke and other gases harmful gas detection. Gas-sensitive element test concentration range: 10 to 1000ppm
TTL output valid signal is low level, (output low signal light, which can be accessed microcontroller IO port).
Size:36mm X24mm X25mm(L * W * H)SKU: sensor_MQ135 - Sensors
MQ2 gas sensor Arduino Compatible ,Methane, Butane, LPG, Smoke Sensor
Analog gas sensor MQ2
Used in gas leakage like smoke methane and liquefied flammable gas
Wide detecting scope, fast response and high sensitivity
Simple drive circuit, stable and long life
Detecting LPG, i-butane, propane, methane, alcohol, hydrogen and smokeSKU: sensor_MQ2 - Accessories, Accessories, Sensors
Sound Sensor Module Sound Detection Module Arduino Other MCU
- Sound sensor module sound detection module main chip: Lm393, electret microphone
- Connector wire length: 245cm
- With 3 sets of servo horns and fittings
- Can be used for sonic lamp, with photosensitive sensors act as sound and light alarm, also can be used in the occasion of voice control and sound detection circuit boards output switch value
SKU: Sound Sensor Module Sound Detection Module Arduino Other MCU - Accessories, Accessories, Sensors
Rain Sensor Raindrop Module
Features:
- FR-04 high-quality double-sided materials on sensor,
- King Size 5.0 * 4.0CM, and with the surface of the nickel plating treatment, against oxidative, conductivity, superior performance and longevity
- Current around 15mA
- Adjustable sensitivity
- Operating voltage 3.3V – 5V DC
- Output: Digital switching outputs (0 and 1) and Analog AO voltage output;
- PCB Size: 3.2cm x 1.4cm
- Wide voltage LM393 comparator
SKU: Rain Sensor Raindrop Module - Accessories, Accessories, Bluetooth, Sensors
Wireless Bluetooth HC-06 Slave Mode Module w/ Backboard
-3%Accessories, Accessories, Bluetooth, SensorsWireless Bluetooth HC-06 Slave Mode Module w/ Backboard
Features:
- CSR Bluetooth Chip Solution
- Bluetooth v2.0+EDR Compliant
- UART interface and with baud rate setup function
- Built-in antenna.
- Coverage up to 30ft.
- Incredible small size with 3.3V input, and RoHS Compliant
- Working current: While pairing 30mA, paired 8mA
- Frequency: 2.4GHz ISM band
- Baud rate is 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 user manually set up.
- Default Baud Rate: 9600,8,1,n
- Support for 8Mbit External Flash Onboard
- Support for 802.11 Co-Existence Product Description
- Storage Temperature: -40 to 85 degrees Celsius
- Size : 28 mm x 15 mm x 2.35 mm
SKU: Wireless Bluetooth HC-06 Slave Mode Module w/ Backboard - Accessories, Accessories, Bluetooth, Sensors
Wireless Bluetooth HC-05 [Master / Slave Mode] Serial Pass-Through Module w/ Backboard
-34%Accessories, Accessories, Bluetooth, SensorsWireless Bluetooth HC-05 [Master / Slave Mode] Serial Pass-Through Module w/ Backboard
Features
- Bluetooth v2.0+EDR
- 2.4GHz ISM band frequency
- Supported baud rate: 9600, 19200,38400(default), 57600, 115200, 230400, 460800.
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
- Typical ‐80dBm sensitivity.
- Up to +4dBm RF transmit power.
- Power supply: 3.6V to 6V DC
- PIO control.
- UART interface with programmable baud rate.
- Built-in antenna.
- Coverage up to 30ft.
- Dimension: 38mm x 15mm x 2.35mm
SKU: Wireless Bluetooth HC-05 [Master / Slave Mode] Serial Pass-Through Module w/ Backboard